0.5mm 3D Printer Extruder Brass Nozzle Makerbot which has outstanding quality and the best performance for DIY and professional systems. By simply adding a holder, you can assemble your own dual head extrusion.

Features

1. Temperature range of use: −40°C to 270°C.
2. Dissipation power factor: ≥5 mW/℃ (static in the air).
3. 100k Ohm NTC Thermistor.
4. NTC Thin Film Thermistor Cable.
5. Max power rating: 45 mW
6. The hot time constant: ≤7 s(in the air)

10mm 100ft High Temperature Heat Resistant Polyimide Koptan Tape Hot serves as the perfect combination of heat resistance (anti-creek property) and Durable Insulation. Extensive use as electrical insulation for transformer , motor , coil , capacitor and frequency conversion power supply in electronic industry.

The 1000mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.

It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw which is mainly used in stepper motor, machine tool rails and other types of equipment.

Compares to the 2004 Smart LCD Controller With Adapter, this 128×64 screen can display much more information, which would help for you run the 3D printer without a computer.

The 215mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.

It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.

The 300mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.

It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.

The 3D printer 128×64 Smart LCD controller for ramps 1.4 contains an SD-Card reader, a rotary encoder and a 128×64 LCD display. You can easily connect it to your RAMPS board using the “smart adapter”.

This 3D Pen is an ideal gift for your kids, your friends, or yourself. Childhood is the best time to develop children’s potential. This 3D printing pen helps to train the children’s outsight, attention, imagination, and creativity. It is also a great way for adults to relieve stress or cultivate interests, let alone a person who is a designer, architect, artist, or crafts lover will love to create anything in mind. This 3D Pen is compatible with both PLA and ABS. More filament, more fun, brings your enjoyable drawing and creating an experience. PLA Filament is produced from organic substances such as corn and sugarcane. This makes PLA plastic non-toxic and has no unpleasant odor, much safer and more comfortable than other 3D Pen filament plastics. There is a Speed Controller on the 3D Pen for you to control the 3D Pen extrusion speed for smoother operation and intricate drawing. Adjustable temperature suits your different needs. It allows you to choose the appropriate melting point (temperature) according to the filament you are using. (PLA:160℃-210℃, ABS:210℃-235℃). The 3D Pen will switch to standby mode automatically when not used for over 5 minutes. The 3D printing pen has a heat dissipation port, protecting the user from scalding. Making use of advanced cooling technology, the filament is heated through the pen body and cooled down before it flows from the nozzle, avoiding the risk of scald. This 3D Printing Pen is designed with a slim body and is lightweight. It is extremely easy to handle just like holding a normal pen; even kids can handle it in a breeze. Simply plug in, heat up, and you are almost ready to go.

Note:

1. DO NOT touch the nib during using it. Please unload the filament after use and turn off the power.
2. DO NOT touch the nozzle before the 3D printing pen cooling.

400mm Trapezoidal Lead Screw 8 mm Thread 2 mm Pitch with Copper Nut is mainly used for Stepping motor driving guide rail. It is made in a T-shape design with high-quality stainless steel material. It is easy to install and convenient to use.

It has good wear resistance and strength, high accuracy, hard to rust, and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motors, machine tool rails, and other types of equipment.

These screws are commonly used in 3D printers, CNC routers, lift mechanisms, and automation projects.

The 500mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.

It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.

Features:-

• Type: KP08
• Material: zinc alloy
• Bore Diameter:8mm
• Mounting Hole Diameter: 5 mm
• Durable with high precision
• Can withstand great weight.

The E3D V6 12V Direct Drive All-Metal Hotend Kit – 1.75mm  Kit from E3D has been redesigned for your convenience from the ground up! This new hot end contains the same signature high-temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments.

Our inventory of this kit has transitioned to the new cartridge-type format for temperature sensors. This kit contains the new thermistor cartridge and heater block.

The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations.

This flexible type motor coupling can connect your driving shaft with the driven shaft while it is very efficient in eliminating any misalignment to the possible extent. Minimum backlash is another great advantage of this Aluminium Flexible Shaft Coupling 5mm x 5mm.

This Flexible coupling with the outer diameter of 19mm and the length of 25mm is machined aluminum coupling.

First bore diameter is 5mm and the second bore diameter is of 5mm also.

It comes with the spiral cut in the middle along its length which makes it flexible so they can be fit to two shafts even if they are not perfectly co-linear and will help reduce binding effects. Such couplings are also known as Beam coupling, helical coupling, Flexible coupling.

Some of the important features of flexible shaft coupling are,

1. Helical cut makes them behave like a springy in the X Y and Z linear axis but not in the rotational axis. That means that you won’t get more backlash, hence they are suitable for precision CNC work.
2. A coupling is a device which transmits power and torque. Couplings do not normally allow disconnection of shafts during operation. However, there are torque limiting couplings which can slip or disconnect when some torque limit exceeds.
3. By careful selection, installation and maintenance of couplings, substantial savings are possible in reduced maintenance costs and downtime.
4. It can protect the driving and driven shaft members against harmful effects because of misalignment of the shafts, sudden shock loads, shaft expansion or vibrations etc.

The E3D V6 12V Direct Drive All-Metal Hotend Kit – 1.75mm  Kit from E3D has been redesigned for your convenience from the ground up! This new hot end contains the same signature high-temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments.

Our inventory of this kit has transitioned to the new cartridge-type format for temperature sensors. This kit contains the new thermistor cartridge and heater block.

The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations.

The 12v 40W Ceramic Cartridge Heater is a powerful little beast of a heater. Get rid of fragile and poor tolerance enamel resistors and switch to a purpose made high power ceramic heater cartridge.

Features:-

1. It is the upgraded version of CR-10.
2. With Filament detector, can reduce accidents and avoid model printing interrupts.
3. With Dual lead screws with motor, more durable to use.
4. Use Industrial-grade PCB mainboard, more highly integrated modules, can continuously print for about 200 hours without pressure, with matures printing technology and stable performance.
5. Only take 10 minutes to install.
6. Use newest V-slot linear bearing system, brings high accuracy and low noise printing.

Features

1. Modelling technology: FDM ( Fused Deposition Modelling）
2. Printing size: 220 x 220 x 250 mm
3. Machine size: 440 x 410 x 465 mm
4. Max traveling speed: 180mm / s
5. Filament: 1.75 mm PLA, TPU, ABS, Gradient color, carbon fiber, etc.
6. Input: AC 100 – 265V, 50 – 60Hz
7. Output: DC 24V, 15 A, 360W
8. Layer thickness: 0.1 – 0.4 mm
9. Nozzle diameter: 0.4 mm
10. Precision: ±0.1 mm.

Features

1. Modeling Technology – FDM（Fused Deposition Modeling).
2. Printing Size – 220*220*250mm.
3. Machine Size – 440*410*465mm.
4. Net Weight – 8KG.
5. Printing Speed – 180mm/s.
6. Filament – 1.75mmPLA, TPU, ABS.
7. Power Supply – 100-265V 50-60HZ.
8. Output – 24V 15A 360W.
9. Layer Thickness – 0.1-0.4mm.
10. Nozzle Diameter – 0.4mm.

Features:-

• Moulding Technology: FDM.
• Print Dimensions: 220*220*300mm.
• Print Speed: <180mm/s, Normal Printing Speed 40-80 mm/s.
• Print Accuracy: + – 0.1mm.
• Layers Thickness: 0.1-0.4mm.
• Nozzle Diameter: Standard 0.4mm. Convertible 0.2, 0.3mm.
• Nozzle Quantity: 1.
• Nozzle Temperature: <260 Degree C
• Hot Bed Temperature: <135 Degree C
• Working Modes: Online or TF Cards are printed offline.
• File Formats: STL, ODJ, AMF.
• Slicing Software: Cura, Repeti-Host, Simlify 3d.
• Power Parameters: Input:110v/220v. 50/60Hz. Output: DC 24V.
• Machine Power: 270W.

This Creality Children CR-100 3d printer 100*100*80mm designed extremely as an innovative design, integrating classic elements, for beginners and children. This 3D printer is capable of providing more consistent, good-quality prints. Using a single extruder type with FDM technology, it offers a total size is 241 x 183 x 255 mm and its build volume is 100 x 100 x 80 mm. Thereby saves space with a small build size. This printer comes with a nozzle diameter of 0.4mm and a filament diameter of 1.75mm.

This All complete Bowden V6 with Fan Cable 30cm Length for 1.75 mm filament 0.2 mm Nozzle contains the same signature high-temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments. This kit contains the old thermistor, heater block, sleeving, cooling fan with holder.

The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations.

With High-Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon – this also eliminates HotEnd meltdown failures that are common with PTFE designs. Even though the v6 has a PTFE liner inside the hotend the liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating. Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate.

The v6 has cut back on a bunch of bulk. This clean-cut version’s overall length is only 62mm, and there are significant reductions in the X/Y dimensions by using the new injection moulded fan duct.

Are you eager to start printing right away? Good. So are we – and that’s why here at MatterHackers we praise the v6 HotEnd. No adhesives, Kapton tape, or soldering is needed to get started. The new v6 simply locks into place with a little screw, high-temp glass sleeving is used to insulate the thermistor legs. This makes installing the hotend (as well as removing) a quick and smooth process compared to earlier methods involving various adhesives. The parts of the hotend just screw together, and the fan duct naturally clips in – this can be manipulated in different ways to suit your setup preference.

This is Aluminum GT2 Timing Pulley 20 Tooth 6.35mm Bore For 6mm Belt. For precise motion control, GT2 belts and pulleys offer excellent precision at a great price. This pulley is meant for use with GT2 6mm wide belts only – MXL belts will slip due to the different tooth profiles.

This pulley has 20 teeth and a 6.35mm inner bore. Two set screws can be used to attach it firmly to any 6.35mm diameter shaft. Full aluminum construction means these are very light and very durable.

Highest quality precision 10M GT2 Width 6mm Black Open Timing Belt For 3D Printer. Made from NEOPRENE – Synthetic Rubber reinforced with fiberglass cords for superior strength. Neoprene – an oil-resistant substitute for natural rubber, was invented by DuPont scientists on April 17, 1930.

Features:-

• Model Number: KFL08
• Material: Zinc Alloy
• Inner diameter: 8mm
• Length: 48mm
• Height: 12mm
• Weight: 26.4g.

Features:-

• Model Number: KFL08
• Material: Zinc Alloy
• Inner diameter: 8mm
• Length: 48mm
• Height: 12mm
• Weight: 26.4g.

This is 3d Printer CNC Lead Copper Nut for 8mm Screw. It is used with 8mm Lead Screw in general machine tools such as 3D printing.

The LM8UU 8 MM Linear Motion Bearing gives you very precise, safe and reliable linear motion system. Such linear motion bearings are mostly used in 3D printers and CNC(Computer Numerical Control) machines. An LM8UU 8 MM Linear Motion Bearing can provide low friction motion along a single axis, hence find a wide range of applications in DIY and robotics prototyping.